top of page

SHARC Assortment of Hydraulic Components for Amada 250 Series Band Saws

Fits Amada 250 Series Saws with Serial Numbers Beginning with 2575 and Equipped with 7720115 Hydraulic pump/motor assembly.

A-7720115-MB

Motor Bushing (Splined Coupling) for Amada Band Saws

This Copper Compression Sealing Washer is used to seal the connection at Banjo Fittings on Various Amada saw.

AS-J-02-3

Copper Sealing Washer for Amada Band Saws

Fits Newer Amada 250 Series Saws equipped with Full Stroke Vises that were manufactured in China. Serial Numbers beginning with 650. This is the correct motor for the U.S. Market as it is a dual voltage motor 230/460 VAC.

A-RB01197

Hydraulic Motor (Motor Only) for Amada Band Saws

Check Nipple / Hydraulic Fitting for Amada Series Band Saws
This is the fitting used on the Blade Tension Assembly to
stop pressure from bleeding off when the saw is shut off.

A-1108399

Check Nipple for Amada Band Saws

This Level Gauge is used on Various Amada Saws to display the Hydraulic Oil Level and on the VM2500 Series it is also used for the Coolant Level.

A-1105018

Level Gauge (Fluid Sight Gauge) for Amada Band Saws

The Oil Cleaner is used primarily to protect the Feed Vise Proportional Valve on various Amada Saws. Due to the extremely tight tolerances present in the Proportional Valve, SHARC recommends a full hydraulic fluid change and new filter (TR-20230) be installed with this seal Kit.

TR-20230-SK

Oil Cleaner Seal Kit for Amada Band Saws

Please use this chart to assist in ordering the proper items for your Amada HA250W. If you need any of the parts without an arrow or any further clarification we will be glad to help.

HA250W Hydraulic Reference - 6503 Serial

Hydraulic Component Chart for Amada HA250W with Serial Numbers Beginning 6503

This Filter is used to protect the Flow and Pressure Controls on Amada Saws.

A-653441

Hydraulic Filter for Amada Band Saws

This Small Filter is Internal to the Filter Check Valve Assembly that Controls the Lift Cylinder.

A-HJ-045-4019A-08-01

Internal Hydraulic Filter for Amada Band Saws

Fits Internally to the Pump Motor Assembly on Older 250 Series Saws
Coupling has "Unequal ID's" to match your Factory Pump and Motor

A-2MY750-C

Spider Coupling for 2MY-750 (10314896) Hydraulic Pump Assembly

This Hydraulic Pressure Switch is Utilized on Various Amada Saws to Signal to the PLC whether the Vises are Opened or Closed

YV-1605

Vise Pressure Switch for Amada Band Saws

This Hydraulic Pump for Amada 250 Series Saws fits Japanese and Taiwanese HA & HFA 250 Saws equipped with Rack & Pawl Vises (Does not fit machines equipped with Full Stroke Vises).  Fits Serial Numbers beginning 250 or 253. Direct Fit, Bolt on Replacement.

A-7921570-P

Hydraulic Pump for Amada Band Saws

This Hydraulic Pressure Gauge is utilized to set the desired pressure of the Bar End Positioning System on various Amada Saws

A-10301624

Hydraulic Pressure Gauge for Amada Band Saws

Please use this chart to assist in ordering the proper items for your Amada HFA250W. If you need any of the parts without an arrow or any further clarification we will be glad to help.

HFA250W Hydraulic Reference - 6505 Serial

Hydraulic Component Chart for Amada HFA250W with Serial Numbers Beginning 6505

Fits newer Amada 250 & 400 Series Saws with the control console mounted to the front right of the machine base.

A-1109078

Legend Plate (Hydraulic) for Amada Band Saws

This Rubber Sheet is used on Various Amada Saws as a sealing gasket for the Hydraulic Sight Gauge and on the VM2500 Series it is also used for the Coolant Level Sight Gauge.

A-1105019

Rubber Sheet (Sight Gauge Gasket) for Amada Band Saws

This Kit is to Rebuild the Tappet Switch Assembly on Amada 250 Saws
Equipped with Rack & Pawl Vises

A-250-TSK

Tappet Switch Cylinder Rebuild Kit for All Amada HA250 & HA250W Saws using Rack & Pawl Vises.

This filter is used primarily to protect the Feed Vise Proportional Valve on various Amada Saws. Due to the extremely tight tolerances present in the Proportional Valve, SHARC recommends a full hydraulic fluid change with the replacement of this filter.

TR-20230

Filter Element for Amada Band Saws

Fits Amada 250 Series Machines with Serial Numbers starting with 650 only.

A-RB0050803

Hydraulic Pump for Amada Band Saws

Please use this chart to assist in ordering the proper items for your Amada HA250 or HA250W. If you need any of the parts without an arrow or any further clarification we will be glad to help.

HA250 Hydraulic Reference - Rack & Pawl

Hydraulic Component Chart for Amada HA250/HA250W with Serial Numbers Beginning 459, 460, 250, 253, 254

Used to add the proper material standards to your Amada Saw Head Feed Control Panel. Comes with all plates shown as a set.

A-1230849a

Material Plate / Material Chart for Amada Band Saws

Used on Various Amada Machines this hydraulic fitting has a Male Pipe Thread on one side and a Male JIS Flare on the other.

A-3001F04

Straight Hydraulic Fitting for Amada Band Saws

This Vinyl Washer is utilized to seal the Oil Level Sight Gauge on various Amada Saws

6X12X1T Vinyl Washer

Clear Vinyl Washer for use with Oil Level Gauge on Amada Band Saws

Fits Amada 250 Series Saws with Serial Numbers Beginning with 2575.

A-7720115

Hydraulic Unit (Pump and Motor Assembly) for Amada Band Saws

This Suction Filter is used primarily as the Hydraulic Tank Pickup on Various Amada Saws

SFT-04-150W

Suction Filter for Amada Band Saws

This Limit Switch is used in conjunction with the Tappet Cylinder on Amada 250 Series Saws equipped with Rack and Pawl Vises.

A-10359521

Limit Switch for Amada Band Saws

Please use this chart to assist in ordering the proper items for your Amada HFA250 or HFA250W. If you need any of the parts without an arrow or any further clarification we will be glad to help.

HFA250 Hydraulic Reference - Rack & Pawl

Hydraulic Component Chart for Amada HFA250/HFA250W with Serial Numbers Beginning 250

This Level Gauge or Sight Gauge is used on Various Amada Saws, calling for any or the listed cross numbers, to indicate Hydraulic Oil or Coolant level.

A-10580109

Level Gauge for Amada Band Saws

Fits Amada HA250W Saws with 2575 Serial Numbers only. Includes new coupling / bushing for motor.

A-7720115-PO

Hydraulic Pump for Amada Band Saws

Fits Amada 250 Series Saws equipped with Rack & Pawl Vises that DO NOT use the Trichoid pump with Spider Coupling. For those saws, you would need the pump / motor assembly part A-7921570.

A-7921570-M

Hydraulic Motor (Motor Only) for Amada Band Saws

This Suction Filter is used primarily as the Hydraulic Tank Pickup on Various Amada Saws

SFT-06-150W

Suction Filter for Amada Band Saws

This Bellows fits Older Amada Series Saws equipped with Rack & Pawl Vises

A-604281

Flex Conduit (Bellows) for Amada Band Saws

Please use this chart to assist in ordering the proper items for your Amada HA250W. If you need any of the parts without an arrow or any further clarification we will be glad to help.

HA250W Hydraulic Reference - 2575 Serial

Hydraulic Component Chart for Amada HA250W with Serial Numbers Beginning 2575

bottom of page